Research Article | OPEN ACCESS
A Mathematical Approach Using Thermoporoelastic Model for Reamer While Drilling Efficiency Analysis and Closeness
1Abbas Roohi, 2Andreas Nascimento, 1Asad Elmgerbi, 1Michael Prohaska and 1Gerhard Thonhauser
1Montanuniversitäaet Leoben (MUL), Department of Petroleum Engineering (DPE), Chair of Drilling and Completion Engineering (CDC), Max-Tendler-Straße 4, 8700, Leoben, Austria
2Departamento de Mecânica (DME)/PRH48-ANP, Faculdade de Engenharia, Universidade Estadual Paulista (UNESP), Câmpus de Guaratinguetá (FEG), Avenida Ariberto Pereira da Cunha 333, Portal das Colinas, 12.516-410 Guaratinguetá, SP, Brazil
Research Journal of Applied Sciences, Engineering and Technology 2016 1:7-14
Received: October ‎19, ‎2015 | Accepted: February ‎10, ‎2016 | Published: July 05, 2016
Abstract
The main objective of this research is to predict the proper bit/reamer size ratio based on the rock strength weakening zone around the wellbore. Nowadays, the Reaming While Drilling (RWD) technology is gaining more and more acceptance in the petroleum industry by means of reducing drilling time and Non-Productive Time (NPT), which results in significant cost saving. The importance of this research is analyzing scenarios in which RWD would add benefit to the operation, given that the reaming process is often fraught with much inefficiency. Thus, through the process of estimation optimum reamer/size ratio, by coupling three key parameters in geo mechanics: thermo-poro-elastic, a model of rock strength is developed to analytically assess how rock strength distribution changes around the wellbores and in particular below the reamer in drilling environments. An analytical model of thermoporoelastic is used with published data (for rock properties usage purposes) in order to develop a model of rock strength below the reamer to show in how far some specific rock could be a good candidate for reamer usage. This in turn allows finding proper candidates for effective RWD applications and also can assist to determine the maximum reamer/bit size ratio for certain rock characteristics in order to optimize the drilling system. From the analysis performed, which was carried considering two different groups in terms of formation permeability, it is be conclusive that for low-permeable formation the size of reamer is function of exposure time of wellbore after making pilot hole while the reamer size for enlargement operation through the permeable formation due to fast diffusion rate is not a time dependent parameter.
Keywords:
Drilling efficiency , pore pressure, reamer , rock strength , thermoporoelastic , temperature,
References
-
Aadnoy, B.S. and R. Looyeh, 2010. Petroleum Rock Mechanics: Drilling Operation and Well Design. Gulf Professional Publishing, Oxford, UK, pp: 53-65.
-
Abousleiman, Y., S. Ekbote, L. Cui, F. Mody, J.C. Roegiers and M. Zaman, 1999. Time-dependent coupled processes in wellbore design and stability: PBORE-3D. Proceeding of the SPE Annual Technical Conference and Exhibition. Houston, Texas.
CrossRef -
Barton, S.P., 2010. Accurate matching of bit and reaming tools delivers optimized drilling performance. Proceeding of the International Oil and Gas Conference and Exhibition. Beijing, China.
CrossRef -
Bencic, A., M. Prohaska, J.T.V. de Sousa and K.K. Millheim, 1998. Slimhole drilling and coring - a new approach. Proceeding of SPE Annual Technical Conference and Exhibition. New Orleans, Louisiana, September 27-30.
CrossRef PMid:9650480 -
Caicedo, H., W. Calhoun and R. Ewy, 2005a. Unique bit performance predictor using specific energy coefficients as a function of confined compressive strength impacts drilling performance. Proceeding of the 18th World Petroleum Congress. Johannesburg, South Africa.
PMCid:PMC1150366 -
Caicedo, H.U., W.M. Calhoun and R.T. Ewy, 2005b. Unique ROP predictor using bit-specific coefficient of sliding friction and mechanical efficiency as a function of confined compressive strength impacts drilling performance. Proceeding of the SPE/IADC Drilling Conference. Amsterdam, Netherlands.
CrossRef PMCid:PMC1150366 -
Calhoun, W., C. Texaco, R. Ewy and C. Texaco, 2005. New confined compressive strength calculation improves bit selection and bit performance. Proceeding of the AADE National Technical Conference and Exhibition. Houston, Texas.
-
Chen, G. and R.T. Ewy, 2004. Thermoporoelastic effect on wellbore stresses in permeable rocks. Proceeding of the 6th North America Rock Mechanics Symposium (NARMS) on Gulf Rocks. Houston, Texas.
-
Chen, G. And R.T. Ewy, 2005. Thermoporoelastic effect on wellbore stability. SPE J., 10(2): 121-129.
CrossRef -
Cui, L., A.H.D. Cheng and Y. Abousleiman, 1997. Poroelastic solution for an inclined borehole. J. Appl. Mech., 64(1): 32-38.
CrossRef -
De Sousa, J.T.V., M. Prohaska, A. Bencic and K.K. Millheim, 1999. Optimization of slimhole dual-body bits by experiments and computational fluid dynamics. Proceeding of the SPE Western Regional Meeting. Anchorage, Alaska.
CrossRef -
Detournay, E. and A.H.D. Cheng, 1988. Poroelastic response of a borehole in a non-hydrostatic stress field. Int. J. Rock Mech. Min., 25(3): 171-182.
CrossRef -
Fjaer, E., 2008. Petroleum Related Rock Mechanics. 2nd Edn., Elsevier, Boston, Amsterdam, pp: 55-340.
CrossRef -
Ho, T., M. Cortez, I. Nott and X. McNary, 2013. Optimal bit, reamer selection and operating procedures improve hole enlargement performance in deepwater Gulf of Mexico. Proceeding of the SPE/IADC Drilling Conference. Amsterdam, The Netherlands.
CrossRef -
Li, X., L. Cui and J.C. Roegiers, 1998. Thermoporoelastic analyses of inclined boreholes. Proceeding of the SPE/ISRM Rock Mechanics in Petroleum Engineering. Trondheim, Norway.
CrossRef -
Ma, R., Y. Ji, H. Wang and F. Han, 2012. Dual-factor method for calculating weight distribution in reaming while drilling. Proceeding of the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition. Tianjin, China.
CrossRef -
Maurer, W.C., 1965. Bit - tooth penetration under simulated borehole conditions. J. Petrol. Technol., 17(12): 1433-1442.
CrossRef -
Meyer-Heye, B., H. Reckmann and G.P. Ostermeyer, 2010. Weight distribution in reaming while drilling BHAs. Proceeding of the IADC/SPE Drilling Conference and Exhibition. New Orleans, Louisiana, USA.
CrossRef -
Radford, S.R., M.E. Hafle, C.C. Ubaru, I.J. Thomson and B. Morel, 2010. Proper bit and underreamer synchronization concept delivered excellent performance in GoM deepwater well. Proceeding of the Offshore Technology Conference. Houston, Texas, USA.
CrossRef -
Tao, Q. and A. Ghassemi, 2007. Porothermoelastic analysis of wellbore failure and determination of in situ stress and rock strength. Proceeding of the 1st Canada-U.S. Rock Mechanics Symposium. Vancouver, Canada.
CrossRef -
Teasdale, P., G. John, R. Davis and N. Baudouin, 2014. Innovative dual-diameter PDC bit design provides unique solution to successful drilling of challenging volcanic interval. Proceeding of the IADC/SPE Drilling Conference and Exhibition. Fort Worth, Texas, USA.
CrossRef -
Warren, T.M. and M.B. Smith, 1985. Bottomhole stress factors affecting drilling rate at depth. J. Petrol. Technol., 37(8): 1523-1533.
CrossRef -
Yang, J.H. and K.E. Gray, 1967. Single-blow bit-tooth impact tests on saturated rocks under confining pressure: II. Elevated pore pressure. Soc. Petrol. Eng. J., 7(4): 389-408.
CrossRef
Competing interests
The authors have no competing interests.
Open Access Policy
This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
Copyright
The authors have no competing interests.
|
|
![](http://www.maxwellsci.com/images/RJASET-maxw.jpg) |
ISSN (Online): 2040-7467
ISSN (Print): 2040-7459 |
![Submit Manuscript](../images/sub.jpg) |
Information |
|
|
|
Sales & Services |
|
|
|